Base Station Installation Tutorial
Last updated
Last updated
You can follow this YouTube video or the content below to install your Base Station.
Plug in the USB-C cable and power the HYFIX device with any 5 volt, 2.5 or 3 amp USB charger.
On the HYFIX device, remove the red plastic from the “WiFi-BT” input, and connect the Wi-Fi antenna.
Remove the red plastic for “GNSS+” and connect the smaller end of the satellite antenna cable. (SMA-Male connector)
Connect the other end to the satellite antenna. (TNC-Male connector)
The "UWB" port is for future expansions and is currently not in use.
Switch your HYFIX unit to the ON position using the small slide switch.
The left red LED (Power) will turn on.
The right green LED (Wi-Fi Internet) should be blinking slowly.
The middle orange LED (PPS) will be off and activated later.
The device is now in the “Access Point Mode” (AP Mode).
Note: We recommend using the provided Wi-Fi antenna, as we have observed issues during testing using random Wi-Fi antennas.
LED
FUNCTION
STATUS
RED
POWER
SOLID, when powered
ORANGE
PPS (Pulse Per Second)
BLINKING (1s), antenna sees satellites
GREEN
Wi-Fi / Internet
BLINKING (SLOW): Access Point mode, used for configuring Internet connection (http://192.168.4.1)
BLINKING (FAST): Attempting to connect to Internet via Configured SSID and Password
BLINKING (1 FAST and 1 SLOW) : WIFI is connected to router but not receiving any internet. (Router may be too far or router may be blocking internet from going to miner)
SOLID, Internet is connected
Now using your phone, PC or MAC to connect to the HYFIX device's Wi-Fi.
You don't need an internet connection for this step.
On your phone, PC or MAC, go into the settings and networks and connect to your HYFIX device's Wi-Fi. It should start with “MGW200_...” or "MobileCM_...".
For password, enter in the serial number that is on the back of your HYFIX device.
Once connected, it may say, “no internet”, that’s okay.
Turn over your HYFIX device and note the number on the sticker. You need this to register to the "console.geodnet.com" later on.
Use the same device as in step 2.0, then enter the IP address 192.168.4.1 and this page will pop up. Some of our miners suggest that Firefox browser works better. For IOS or Mac device, setup page should pop up automatically after entering password.
Miner Key: must be at least 12 characters long and contain no special characters.
If the green light starts flashing again, the Base Station has not been connected to Wi-Fi. Please check if you have connected it correctly and try again.
When the station gets a full green light, you can go over to your PC/Tablet that is connected to the same internet you connected your station to.
Now open your internet router’s webpage and check the current connected devices on your Wi-Fi.
In the Router Settings you will find the MobileCM listed as: espressif.
Note the IP-Adress of espressif: 192.168.x.x.
You need to access on the MobileCM WebUI (Station Mode).
Please be sure again you use 2.4GHZ Wi-Fi. (5GHz is not compatible with the MobileCM).
Go into your router settings, you do that through your web browser, by entering your routers own IP address.
Follow a link on how to find that for both windows and mac users: https://www.howtogeek.com/233952/how-to-find-your-routers-ip-address-on-any-computer- smartphone-or-tablet/
If you live in an apartment with shared Wi-Fi, and you have problems with this, you can just call your internet provider and ask them for help. And you ask them the same thing that you will be looking for inside the router settings. “You are looking for the IP address of a device named espressif”.
When you have the IP address (IP 192.168).x.x enter it into your browser, and this page should pop up.
If you see the word “TRANSMITTNG”, the setup is complete.
Useful information if you change location or have made a mistake in setup:
For those interested, pressing the “reset” key on the back resets the device back to AP-Mode. Then, proceed with the basic setup again to update to the new Wi-Fi.
This is really useful when moving locations.
Please double check your Wi-Fi name and password was entered correctly.
If it fails to connect due to mistakes in password or network name, please try again.
Turn over your HYFIX device and note the number on the sticker. You need this to access the Console platform at console.geodnet.com.
